2 x 100W Bluetooth 5.0 Multipoint Stereo Audio Amplifier Board

Description: TSA2500 is a 2x100W Stereo Bluetooth 5 multipoint audio amplifier board. It has perfect class-D architecture(Based on TDA7498) and each channel has maximum 100W power output. Both of channels are capable of outputting nominal power simultaneously and continuously. This board can be powered by any DC14V-39V power supply. it can be used to drive any 4Ω or 8Ω passive speakers.The highlight point is BT 5 integrated. You can have many TSA2500 boards paired and work together. TSA2500 can remember the pairing info. You don't need pair them each time after you turn the amplifier board on. This makes it possible to build a wireless surround sound system by using the TSA2500.If you only use one TSA2500. It can works like a common Bluetooth amplifier board. Power the amplifier board. Double click PAIR button to set the board into Pairing mode. Use your phone or PC (etc) to search for a new Bluetooth device. The module will appears as "TSA2500". You don't need a PIN, pair it and then you can play music.Pairing buttons:PAIR - Double click into pairing mode.TX - Click into transimitter mode.RX - Click into receiver mode.External Pairing buttons Port: Connect external buttons to control the PAIR/TX/RX.Play,Volume control Port: Connect external buttons to control the music Play/Pause, Volume+, Volume-. One board works like a normal Bluetooth amplifier Multiple boards work together How to Use:Master board:Power up the TSA2500, Blue LED slow blink. (Voice: Power ON)Double click PAIR button to set the TSA2500 into Pairing mode. Blue LED fast blink. (Voice: Pairing)Now, Your smartphone will be able to find a new Bluetooth device which name is "TSA2500". Connect it. (Voice: Pairing successful)You can play the music now. If you only use one amplifier board. You don't need do the following steps.Click TX button, Set the module to transmitter mode, Red LED ON.(Voice: Broadcast mode)Slave board:Power up another TSA2500. Blue LED slow blink.Make sure master board already working correct and in transmitter mode. Click RX button to set slave board into receiver mode. It will auto searching the master board. Green LED ON (Voice: Broadcast audio enabled)Double click the RX button on the Slave board, double click the TX button on the Master board. The master board will auto searching(30s) slave board. Both master and slave board will be connected. (Voice: Pairing successful)The slave board will have music out now.If there have new board want join as slave board. Just click RX on new board into receiver mode then Double click RX, and Double click TX on Master module.If a slave board want quit. Click TX button on that module. Note: If you don't hear the voice prompt when click TX . Please click the RX to switching the mode and then click TX again. Following table lists all typical data of the Amp board. For full specification, please refer to the data sheet of ST's TDA7498 chip. TA = 25 °C, fIN = 1 kHz sine wave, RL= 6Ω, VCC = 36V. (Unless otherwise stated) ParameterConditionMinTypMaxSupply Voltage (VDC)-14-39Quiescent Current (mA)FAN ON,STBY Disable-90-FAN ON,STBY Enable-50-FAN OFF,STBY Disable-40 FAN OFF,STBY Enable 10 Input Sensitivity (mV)25.6dB-1356-31.6dB69635.1dB46037.6dB341Input Impedance (Kohm)-4860-Gain (dB)GAIN0 = L, GAIN1 = L24.625.626.6GAIN0 = L, GAIN1 = H30.631.632.6GAIN0 = H, GAIN1 = L34.135.136.1GAIN0 = H, GAIN1 = H36.637.638.6Output Power (W rms)THD = 10%-100-Efficiency (%) Both channels output rating power->90-Minimum Load (ohm)--6-Frequency Response (dB)±3dB20-22kOperating Temperature (℃)-02050 Features:Size: 120*80*20mmMultipoint connectionBluetooth 5.1Up to 100 boards can be linked together.Qualcomm cVc audio technologyQualcomm TrueWireless TechnologyStereo receiveEffective transmission distance: 10-15mCompatible with all Bluetooth devices that support media audio, including iPhone

Price: 54.5 USD

Location: Hefei, Anhui

End Time: 2024-09-11T08:51:32.000Z

Shipping Cost: 5 USD